6A7-26 6.2 LITER DIESEL
Tig h ten
Bolt (131) to 90 N m (65 ft. lbs.).
OIL PAN INSTALLATION
|-K~| Install or C o nnect (Figure 43)
• Apply a 5 mm (3/ie-inch) bead of RTV sealant (GM
part number 1052915 or equivalent) to the oil pan
sealing surface, inboard of the bolt holes (figure 40).
The sealer must be wet to the touch when the oil
pan is installed.
1. Oil pan
rear
seal to the oil pan.
2. Oil pan to the engine.
3. Bolts (133).
Tig h ten
All except rear two bolts to 10.0 N m (84 in.
lbs.).
— Rear two bolts to 23 N-m (17 ft. lbs.).
INJECTION PUMP
INSTALLATION
-►<- Install or C o nnect (Figure 44)
1. Gasket (103) to the front cover.
2. Injection pump (100).
3. Throttle spring bracket (102).
4. Nuts (101). Leave finger tight until the injection
pump tim ing is adjusted.
5. Injection pump gear (106). Align the slot in the
injection pump with the locating pin on the injection
pump hub (107).
Im p o rtan t
• Align the timinq marks (fiqure 44).
6. Bolts (105).
T ig h ten
• Bolts (105) to 25 N-m (20 ft. lbs.).
7. Wires and hoses at the injection pump.
A djust (Figure 45)
Injection pump timing. For the engine to be properly
timed, the marks on the top of the engine front cover
must be aligned with the marks on the injection
pump flange (figure 45). The engine must be off
when the tim ing is reset.
£
T ig h ten (Figure 44)
Nuts (101) to 40 N-m (30 ft. lbs.).
TORSIONAL DAMPER
INSTALLATION
Install or C onnect (Figure 39)
Torsional dam per (79). Tap into place with a mallet.
Make sure the key is in place. Make sure the
dam per is all the way on the crankshaft.
Bolt (80) and washer (81).
B-07637
Figure 4 2 — M arking TD C on th e Front C over
Summary of Contents for 1989 Light Duty Truck
