GCC Technologies RX Series User Manual Download

Page: 152 / 178

Jaguar IV User Manual

GreatCut Instruction A-5

Advanced Settings

Segmental Positioning

For precise cutting quality, it is suggested to apply “Segmental Positioning” by adjusting the x and y

distance when you are working on an extra long or large-size image to increase cutting quality.

Follow the same steps in the 4-Point Positioning section to complete the contour line setting and

registration mark creation procedures. Adjust the size, object margin and line thickness of your

registration marks and the space between registration marks by changing X, Y distance in the

Setup-Jog Marks window and click OK.

Segmental Positioning

Max.

x Distance:

The distance of

intermediate position on the X axis

Range: 200-500 mm

Max.

y Distance:

The distance of

intermediate position on the Y axis

Range: 200-500 mm

Summary of Contents for RX Series



















































































































































































Search results

Summary of Contents for RX Series

Reviews:

Related manuals for RX Series

Brands by name

Popular brands

GCC Technologies RX Series, User Manual

Search results

Summary of Contents for RX Series

Reviews:

Related manuals for RX Series

Brands by name

Popular brands