GCC Technologies RX Series User Manual Download

Page: 88 / 178

RX Series User Manua

Trouble Shooting 7-4

7.4 Software Problems

Check the following first:

Does your software package indicate that it will work with

your computer and cutting plotter?

Does your software support HP-GL and HP-GL/2 drivers?

(* check the configuration settings of your software.)

Yes

Does the cutting plotter interface

match the requirements of your

software?

Does your

software

recommend

using a different

cable?

Does the software

vendor provide a

sample file?

Most well known cutting softwares

in the world have drivers for our

cutting

plotters.

not,

use

software that has HP-GL and

HP-GL/2 emulation supports and

you can chose the following three

drivers:

A3 size: HP7475A

A1 size: HP7580A

A0 size: HP Draf Pro Exl or

HP Draf Master

Yes

Refer to Chapter

2 - Connecting

your cutting

plotter.

Yes

Try using the

recommende

d cable.

Yes

Re-power on the

cutting plotter and

try to send the file

again.

Do something about the

error message display on

LCM, or consult your

software vendor.

Summary of Contents for RX Series



















































































































































































Search results

Summary of Contents for RX Series

Reviews:

Related manuals for RX Series

Brands by name

Popular brands

GCC Technologies RX Series, User Manual

Search results

Summary of Contents for RX Series

Reviews:

Related manuals for RX Series

Brands by name

Popular brands