GCC Technologies RX Series User Manual Download

Page: 89 / 178

RX Series User Manua

Trouble Shooting 7-5

7.5

Cutting Quality Problems

Is the blade installed correctly and the blade

holder fastened securely?

Yes

Is the blade dull

or chipped?

Yes

Replace

with a new

blade

Is tool force set up

properly? (The default

for tool force is 80 gf)

Yes

Adjust the tool force to obtain an

optimum blade force. Refer to

Chapter 4.3 “Cutting Force and

Offset Adjustment”

Is the tool offset set up

properly?

Yes

Adjust the tool offset to

obtain an optimum value.

Is there any dirt adhered to

the blade?

Yes

Refer to Chapter 2.4

“ Blade Installation”

Remove the blade

and clean it.

Please contact your dealer for technician

support.

Note: The daily maintenance of your cutting plotter is very important.

Be sure to clean up the grid drum and pinch rollers regularly for

better cutting accuracy and output quality.

Summary of Contents for RX Series



















































































































































































Search results

Summary of Contents for RX Series

Reviews:

Related manuals for RX Series

Brands by name

Popular brands

GCC Technologies RX Series, User Manual

Search results

Summary of Contents for RX Series

Reviews:

Related manuals for RX Series

Brands by name

Popular brands