GCC Technologies RX Series User Manual Download

Page: 85 / 178

RX Series User Manua

Trouble Shooting 7-1

This chapter is to help you correct some common problems you may come across. Prior to

getting into the details of this chapter, please be sure that your application environment is

compatible with the cutting plotter.

Possible Causes:

7.1

Non-Operational Problems

Check the following first:

Does the AC power cord plug in properly?

Does the AC power cord connected to the power connector properly?

Does the power LED still illuminate?

Solutions:

If the LCM is able to display the message, the cutting plotter should be in a normal

condition. Switch off the cutting plotter and turn it on again to see if the problem still

existing.

If the LCM is not able to display any message, contact the technician from your dealer.

Note:

Before having your cutting plotter serviced, please

make certain that the malfunction is in your cutting

plotter, not the result of an interface problem or a

malfunction in your computer or a software problem.

Why is the cutting plotter not functioning?

7. Trouble Shooting

Summary of Contents for RX Series



















































































































































































Search results

Summary of Contents for RX Series

Reviews:

Related manuals for RX Series

Brands by name

Popular brands

GCC Technologies RX Series, User Manual

Search results

Summary of Contents for RX Series

Reviews:

Related manuals for RX Series

Brands by name

Popular brands