GCC Technologies RX Series User Manual Download

Page: 75 / 178

RX Series User Manual

Automatic-Aligning System

5-1

Chapter 5 Automatic-Aligning System

Please note that this chapter is only an instruction to AASII; for step-by-step instructions, please

refer to the following chapters:

08_A-3 CorelDraw Plug-In, 08_A-5 GreatCut, 08_A-6 Illustrator.

5.1

Introduction

The RX series cutting plotters feature a standard Automatic-Aligning System (AAS II) to

guarantee precise contour cutting quality by detecting the registration marks printed around the

graphic.

Notice

Avoid any kind of light source horizontally illuminating the AAS module.

- PROHIBITED - ACCEPTABLE

DO NOT take off the cover of AAS module while in operation.

- PROHIBITED

Summary of Contents for RX Series



















































































































































































Search results

Summary of Contents for RX Series

Reviews:

Related manuals for RX Series

Brands by name

Popular brands

GCC Technologies RX Series, User Manual

Search results

Summary of Contents for RX Series

Reviews:

Related manuals for RX Series

Brands by name

Popular brands