GCC Technologies RX Series User Manual Download

Page: 92 / 178

RX Series User Manual

Blade Specification A-2

For cutting thick fluorescent and reflective vinyl. Also for cutting
detailed work in standard vinyl.

20200159G

The blade is 45° with Red Cap(5-unit package), 0.25 mm offset

For cutting reflective vinyl, cardboard, sandblast, flock, and
stencil sharp edge.

265012020G

The blade is 60° with Green Cap, 0.50 mm blade offset

For cutting thin sandblast mask and stencil with friction feed or
sprocket feed machine.

26500059G

The blade is 60° with Blue Cap, 0.25 mm blade offset

For Cutting small text and fine detail. Sharp blade with smallest

offset.

26500060G

The blade is 0.175 mm blade offset with Black Cap

265012840G

For thin and delicate media such as window tint.

The blade is 25° with Yellow Cap, 0.25 mm blade offset

Blade Specification

Summary of Contents for RX Series



















































































































































































Search results

Summary of Contents for RX Series

Reviews:

Related manuals for RX Series

Brands by name

Popular brands

GCC Technologies RX Series, User Manual

Search results

Summary of Contents for RX Series

Reviews:

Related manuals for RX Series

Brands by name

Popular brands