GCC Technologies RX Series User Manual Download

Page: 27 / 178

RX Series User Manual

Installation

2-14

Figure 2-29

Figure 2-28

4. When blade holder and blade length tests are finished, the screen will show you to what

degree (the unit of the value following “CW” or “CCW” is “circle”) and in which direction

[CW (clockwise) or CCW (counterclockwise)] you should turn the adjustment knob.

EG, Turn CW 5 is telling you that you should turn the knob for 5 units clock-wisely (Figure

2-28, Figure 2-29).

5. The screen will show "Adjustment completes" when the value on the screen is 0, the blade

length is perfect and no more adjustment needs to be made. Press "Enter" now to

complete the process and you may start cutting at this point.

Summary of Contents for RX Series



















































































































































































Search results

Summary of Contents for RX Series

Reviews:

Related manuals for RX Series

Brands by name

Popular brands

GCC Technologies RX Series, User Manual

Search results

Summary of Contents for RX Series

Reviews:

Related manuals for RX Series

Brands by name

Popular brands