GCC Technologies RX Series User Manual Download

Page: 97 / 178

RX series User Manual

CorelDRAW Plug-In A-3

Add Registration Mark by page size

If you tick “Add Registration Mark by page size” as shown in the figure below and click “Apply”,

your registration marks will be created automatically.

Note:

1. The length setting will be in the range of 5-25mm

according to your page size.

2. Please DO NOT make any changes to the “Origin”

section when you choose to add registration marks by

page size as indicated below otherwise the position of

the marks will be changed.

The system will create the 4 marks on the 4 corners of the page as shown in the picture below

wherever you move your image.

Summary of Contents for RX Series



















































































































































































Search results

Summary of Contents for RX Series

Reviews:

Related manuals for RX Series

Brands by name

Popular brands

GCC Technologies RX Series, User Manual

Search results

Summary of Contents for RX Series

Reviews:

Related manuals for RX Series

Brands by name

Popular brands