GCC Technologies RX Series User Manual Download

Page: 135 / 178

Jaguar IV User Manual

GreatCut Instruction A-5

Note:

1. To save your materials, in addition to amending object margins, you can also adjust the length of

the registration marks (5mm minimum) when you apply the above function(see table 1 for

suggestions based on different material sizes). The smaller the size is, the smaller the distance

between the object and the registration marks is (see the figures below).

Table 1

*25mm is the suggested value for the registration mark length

2. The size of the registration marks would affect the accuracy of registration mark detection so

please make sure the amount you enter is reasonable.

Page size

(unit: mm)

Suggested mark length

(unit: mm)

A6 (105 x 148)

A5 (148 × 210)

A4 (210 × 297)

A3 (297 × 420)

A2 (420 × 594)

A1 (594 × 841) and above

25*

Area to be cut

Summary of Contents for RX Series



















































































































































































Search results

Summary of Contents for RX Series

Reviews:

Related manuals for RX Series

Brands by name

Popular brands

GCC Technologies RX Series, User Manual

Search results

Summary of Contents for RX Series

Reviews:

Related manuals for RX Series

Brands by name

Popular brands