GCC Technologies RX Series User Manual Download

Page: 112 / 178

RX Series User Manual

SignPal 10.5 Instruction A-4

13. Check which icons and preferences you want to install:

•

Check Install to desktop to install a shortcut for the software on the desktop.

•

Check Install to startup items to install a shortcut for the software in the Startup folder

of the Start menu. If this is done, each time the computer starts up, the software will

automatically start up and minimize itself, displaying an icon in the system tray of the

Windows system tray.

•

Check Clear Application's previous preferences to clear the preferences or clear the

check box to retain old preferences.

•

Click OK.

Summary of Contents for RX Series



















































































































































































Search results

Summary of Contents for RX Series

Reviews:

Related manuals for RX Series

Brands by name

Popular brands

GCC Technologies RX Series, User Manual

Search results

Summary of Contents for RX Series

Reviews:

Related manuals for RX Series

Brands by name

Popular brands