GCC Technologies RX Series User Manual Download

Page: 101 / 178

RX series User Manual

CorelDRAW Plug-In A-3

Note:

To save your materials, in addition to amending object margins, you can also adjust the

length of the registration marks (5mm minimum) when you apply 4-Point Positioning (see

table 1 for suggestions based on different material sizes). The smaller the size is, the smaller

the distance between the object and the registration marks is (see the figures below).

Page size

(unit: mm)

Suggested mark length

(unit: mm)

A6 (105 x 148)

A5 (148 × 210)

A4 (210 × 297)

A3 (297 × 420)

A2 (420 × 594)

A1 (594 × 841) and above

Table 1

25mm is the suggested value for the registration mark length

2. The size of the registration marks would affect the accuracy of registration mark detection

so please make sure the amount you enter is reasonable.

3. If you change the paper size, you will have to reset the registration marks otherwise the

previous setting will be applied.

Area to be cut

Summary of Contents for RX Series



















































































































































































Search results

Summary of Contents for RX Series

Reviews:

Related manuals for RX Series

Brands by name

Popular brands

GCC Technologies RX Series, User Manual

Search results

Summary of Contents for RX Series

Reviews:

Related manuals for RX Series

Brands by name

Popular brands