GCC Technologies RX Series User Manual Download

Page: 99 / 178

RX series User Manual

CorelDRAW Plug-In A-3

Add Registration Mark by Object

If you tick “Add Registration Mark by Object”, you will be offered three options of registration

marks as shown below.

Note: The values entered in the “4-Point Positioning” section (length, thickness and margin) will

still be applied when you tick “Segmental Positioning” or “Multiple Copies”.

4-Point Positioning

Length: The length of marks

Range: 5mm~50mm

Optimized Setting: 25mm

Thickness: The line thickness of marks

Range: 1mm~2mm

Optimized Setting: 1mm

Margin: The distance between marks and images

Range: 0mm~50mm

Optimized Setting: 5mm

Segmental Positioning

X Step: The distance of intermediate position on the X axis

Y Step: The distance of intermediate position on the Y axis

Range: 200mm~600mm

Optimized Setting: Less than 500mm

Multiple Copies

No. of X Copies: The numbers of copies on X axis

No. of Y Copies: The numbers of copies on Y axis

Range: 1~50. (The more copies you make, the more time

is needed for data transmission.)

Numbers of X Copies * Numbers of Y Copies = The total

amount of image copies

Copies with outline

：

To show outlines of image graphics

Summary of Contents for RX Series



















































































































































































Search results

Summary of Contents for RX Series

Reviews:

Related manuals for RX Series

Brands by name

Popular brands

GCC Technologies RX Series, User Manual

Search results

Summary of Contents for RX Series

Reviews:

Related manuals for RX Series

Brands by name

Popular brands