GCC Technologies RX Series User Manual Download

Page: 14 / 178

RX Series User Manual

Installation

2-1

2.1 Precaution

Please read below information carefully before you start installation.

Notice 1

Make sure the power switch is off before installing the cutting plotter.

Carefully handle the cutter to prevent any injuries.

Notice 2 Choosing a proper place before setting up the cutting plotter

Before installing your cutting plotter, select a suitable location, which meets the following

conditions.

The machine can be approached easily from any direction.

Keep enough space for the machine, accessories and supplies.

Keep the working area stable, avoiding sever vibration.

Keep the temperature between 15 and 30

℃

(60-86

F) in the workshop.

The relative humidity of the working environment should be between 25% to 75%.

Protecting the machine from dust and strong air current.

Preventing the machine from direct sunlight or extremely bright lighting.

Notice 3 Connecting the Power Supply

Check the plug of the power cord to see if it matches with the wall outlet. If not, please contact

your dealer.

Insert the plug (male) into a grounded power outlet.

Insert the other end (female) of power cord into the AC connector of cutting plotter.

2. Installation

Summary of Contents for RX Series



















































































































































































Search results

Summary of Contents for RX Series

Reviews:

Related manuals for RX Series

Brands by name

Popular brands

GCC Technologies RX Series, User Manual

Search results

Summary of Contents for RX Series

Reviews:

Related manuals for RX Series

Brands by name

Popular brands