Fujitsu Server PRIMERGY TX1330 M1 Upgrade And Maintenance Manual Download Page 181

Page: 181 / 336

TX1330 M1

Upgrade and Maintenance Manual

181

Expansion cards and backup units

9.4.2.3

Installing a PCI slot bracket

CAUTION!

Always replace slot brackets into unused PCI slot openings to comply
with applicable EMC regulations and satisfy cooling requirements.

Figure 101: Installing a PCI slot bracket

Insert a PCI slot bracket into the unused PCI slot opening (1).

Clip on the PCI slot bracket clamp (2).

Fold down the locking handle on the PCI slot bracket clamp until it locks in
place (3).

9.4.2.4

Concluding steps

"Installing the fan module" on page 152

"Reassembling" on page 58

"Connecting the server to the mains" on page 67

"Switching on the server" on page 68

"Enabling BitLocker functionality" on page 90

Summary of Contents for Server PRIMERGY TX1330 M1

















































































































































































































































































































































Search results

Summary of Contents for Server PRIMERGY TX1330 M1

Reviews:

Related manuals for Server PRIMERGY TX1330 M1

Brands by name

Popular brands

Fujitsu Server PRIMERGY TX1330 M1, Upgrade And Maintenance Manual

Search results

Summary of Contents for Server PRIMERGY TX1330 M1

Reviews:

Related manuals for Server PRIMERGY TX1330 M1

Brands by name

Popular brands