manualshive.com logo in svg

Fujitsu Server PRIMERGY TX1330 M1, Upgrade And Maintenance Manual, Page: 109 / 336

Share
Download
Fujitsu Server PRIMERGY TX1330 M1 Upgrade And Maintenance Manual Download Page 109

TX1330 M1

Upgrade and Maintenance Manual

109

Power supply

6.3.2

Removing a hot-plug power supply unit

I

Note for servers using CMA (Cable Management Arm)

Regarding of removing power supply units, additional tasks are needed, 
due to an interference between CMA stopper and the power supply units.

Ê

Unlock the CMA stopper.

Ê

Remove the CMA stopper with the mounted crossbar.

Ê

Support the CMA stopper, the crossbar and the CMA including cables 
with your right hand.

Ê

Remove the power supply unit and install a dummy cover into the 
empty bay.

Ê

Remount the complete assembly (CMA stopper, crossbar and CMA) 
into the rail.

6.3.2.1

Preliminary steps

Ê

Disconnect the power cord from the hot-plug power supply unit (see 

"Disconnecting the server from the mains" on page 46

).

Customer Replaceable Unit
(CRU)

Hardware: 5 minutes

Tools:

tool-less

Summary of Contents for Server PRIMERGY TX1330 M1

















































































































































































































































































































































Reviews:

No comments