Home
/
Fujitsu
/
Server PRIMERGY TX1330 M1
/
Upgrade And Maintenance Manual

Fujitsu Server PRIMERGY TX1330 M1, Upgrade And Maintenance Manual, Page: 300 / 336

Share

Page: 300 / 336

Fujitsu Server PRIMERGY TX1330 M1 Upgrade And Maintenance Manual Download Page 300

300

Upgrade and Maintenance Manual

TX1330

M1

Converting a tower model to a rack model

15.3 Concluding steps

Ê

"Installing the top cover" on page 59

Ê

Mount the support bracket and rack mounting rails in the rack as described
in the "Rack Mounting Kit - RMK-F2 Drop-In" Mounting Instructions.

I

The document is available online at

http://manuals.ts.fujitsu.com

(EMEA market) or

http://jp.fujitsu.com/platform/server/primergy/manual/

(Japanese market).

Ê

"Mounting the server in the rack" on page 60

Ê

Reconnect all external cables.

Ê

"Connecting the server to the mains" on page 67

Ê

"Switching on the server" on page 68

Ê

Update your server’s chassis information on the Chassis ID EPROM
integrated into the front panel board. For further information on how to obtain
and use the

ChassisId_Prom

Tool, refer to section

"Using the Chassis ID

Prom Tool" on page 93

.

Ê

"Specifying the chassis model" on page 95

Ê

"Enabling BitLocker functionality" on page 90

«
...
298
299
300
301
302
...
»

Summary of Contents for Server PRIMERGY TX1330 M1

















































































































































































































































































































































Reviews:

No comments