Fujitsu Server PRIMERGY TX1330 M1 Upgrade And Maintenance Manual Download Page 61 | Manualshive

Page: 61 / 336

background image

TX1330 M1

Upgrade and Maintenance Manual

61

Basic hardware procedures

Figure 16: Mounting the server onto the rack rails

V

CAUTION!

Ensure that the safety lock has been properly inserted into the snap fit
lock. For further information, refer to the "Rack Mounting Kit - RMK-F2
Drop-In" Mounting Instructions.

Ê

Fully extend the telescopic rails until they lock in place (1).

Ê

At a slight angle, lower the server onto the rear mounting point on the
telescopic rails (2).

Ê

Fold down the server (3). Ensure that the mounting bolts and the hooks are
properly seated in the mounting points on the telescopic rails and that the
locking bars engage (4).

«
...
59
60
61
62
63
...
»

Summary of Contents for Server PRIMERGY TX1330 M1

















































































































































































































































































































































Reviews:

No comments

Related manuals for Server PRIMERGY TX1330 M1

Brand: IBM Pages: 84

Brand: IBM Pages: 110

Brand: Xerox Pages: 220

Brand: Xerox Pages: 28

DocuPrint 100MX

Brand: Xerox Pages: 2

Brand: Vicon Pages: 2

totalstorage 200

Brand: IBM Pages: 152

Brand: SEH Pages: 5

SuperServer 5013C-MT

Brand: Supero Pages: 98

Flex System p270 Compute Node

Brand: IBM Pages: 510

Brand: TAPKO Pages: 2

Brand: BlueNet Video Pages: 38

ProLiant ML350 G3

Brand: HP Pages: 44

ProLiant ML310e Gen8 v2

Brand: HP Pages: 43

ProLiant ML330 Generation 3

Brand: HP Pages: 34

PROLIANT ML350 G6

Brand: HP Pages: 145

ProLiant ML350 Gen9

Brand: HP Pages: 171

PROLIANT ML350 G6

Brand: HP Pages: 103

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands