manualshive.com logo in svg

Fujitsu Server PRIMERGY TX1330 M1, Upgrade And Maintenance Manual, Page: 237 / 336

Share
Download
Fujitsu Server PRIMERGY TX1330 M1 Upgrade And Maintenance Manual Download Page 237

TX1330 M1

Upgrade and Maintenance Manual

237

Accessible drives

12.2.5 Installing an accessible drive

Figure 146: Opening the accessible drive locking bar

Ê

Press out on the locking latch to disengage the accessible drive locking bar 
(1).

Ê

Fold up the accessible drive locking bar (2).

I

Unlocking and securing the front panel and accessible drives is 
illustrated by the example of tower servers. In case of rack servers, the 
accessible drive locking bar is located on the side of the drive bay. In this 
case, proceed as follows:

Figure 147: Opening the accessible drive locking bar (rack systems)

Ê

Pull up on the locking latch to disengage the accessible drive locking 
bar (1).

Ê

Fold out the accessible drive locking bar (2).

Summary of Contents for Server PRIMERGY TX1330 M1

















































































































































































































































































































































Reviews:

No comments