Fujitsu Server PRIMERGY TX1330 M1 Upgrade And Maintenance Manual Download Page 233

Page: 233 / 336

TX1330 M1

Upgrade and Maintenance Manual

233

Accessible drives

Removing accessible drive covers

Figure 139: Removing an accessible drive covers

Removing accessible drive covers is illustrated by the example of the
tower server. In case of the rack front cover, the procedure is identical.

Turn the front cover face down.

Press in on the lugs on either side of the drive cover.

Fold up (1) and remove the desired accessible drive covers (2).

Summary of Contents for Server PRIMERGY TX1330 M1

















































































































































































































































































































































Search results

Summary of Contents for Server PRIMERGY TX1330 M1

Reviews:

Related manuals for Server PRIMERGY TX1330 M1

Brands by name

Popular brands

Fujitsu Server PRIMERGY TX1330 M1, Upgrade And Maintenance Manual

Search results

Summary of Contents for Server PRIMERGY TX1330 M1

Reviews:

Related manuals for Server PRIMERGY TX1330 M1

Brands by name

Popular brands