Fujitsu Server PRIMERGY TX1330 M1 Upgrade And Maintenance Manual Download Page 162

Page: 162 / 336

162

Upgrade and Maintenance Manual

TX1330

Expansion cards and backup units

9.2

Handling slot brackets

9.2.1

Installing a slot bracket

Use the following slot bracket for the ModularRAID controllers based on
LSI MegaRAID:

– Full height bracket not-perforated

Figure 76: Perforated and non-perforated slot brackets

Upgrade and Repair Unit
(URU)

Hardware: 5 minutes

Tools:

Phillips PH2 / (+) No. 2 screw driver

Full height bracket non-perforated

Full height bracket perforated

Low profile bracket perforated

Summary of Contents for Server PRIMERGY TX1330 M1

















































































































































































































































































































































Search results

Summary of Contents for Server PRIMERGY TX1330 M1

Reviews:

Related manuals for Server PRIMERGY TX1330 M1

Brands by name

Popular brands

Fujitsu Server PRIMERGY TX1330 M1, Upgrade And Maintenance Manual

Search results

Summary of Contents for Server PRIMERGY TX1330 M1

Reviews:

Related manuals for Server PRIMERGY TX1330 M1

Brands by name

Popular brands