Fujitsu Server PRIMERGY TX1330 M1 Upgrade And Maintenance Manual Download Page 77

Page: 77 / 336

TX1330 M1

Upgrade and Maintenance Manual

Basic software procedures

Fujitsu does not assume responsibility for any damage done to the
server or for the loss of any data resulting from BIOS updates.

5.2.1.1

Updating or recovering the system board BIOS

BIOS flash procedure

Perform the BIOS flash procedure as described in your server’s "BIOS
Setup Utility" reference manual.

BIOS recovery procedure

Perform the BIOS recovery procedure as described in your server’s "BIOS
Setup Utility" reference manual.

5.2.1.2

Updating or recovering the iRMC

iRMC flash procedure

Prepare a USB stick including the bootable iRMC firmware update image.

Connect the USB stick to the USB port.

Ensure that only the USB device with the iRMC firmware is connected
to the USB port. Remove all other USB devices temporarily.

Restart the server.

The system will detect the USB stick.

If the BIOS cannot identify the USB stick, the pop-up message

Failed to boot for Emergency flash. Please Reset now.

will show up in the center of the screen.

Choose one of the following options from the update tool menu to start the
iRMC update process:

Normal

Choose this option to update an existing system board.

Initial

Choose this option if the system board has been replaced prior to the

iRMC update procedure. This option will perform all relevant flash
procedures in a row, including the iRMC firmware and bootloader.

Summary of Contents for Server PRIMERGY TX1330 M1

















































































































































































































































































































































Search results

Summary of Contents for Server PRIMERGY TX1330 M1

Reviews:

Related manuals for Server PRIMERGY TX1330 M1

Brands by name

Popular brands

Fujitsu Server PRIMERGY TX1330 M1, Upgrade And Maintenance Manual

Search results

Summary of Contents for Server PRIMERGY TX1330 M1

Reviews:

Related manuals for Server PRIMERGY TX1330 M1

Brands by name

Popular brands