manualshive.com logo in svg

Fujitsu Server PRIMERGY TX1330 M1, Upgrade And Maintenance Manual

The Fujitsu Server PRIMERGY TX1330 M1 is a high-performance server offering exceptional reliability and scalability. Ensure efficient operation and optimize performance with the Upgrade and Maintenance Manual, available for free download from our website. This comprehensive manual provides valuable insights and step-by-step instructions, enabling users to successfully maintain and upgrade their server.

Share
Download
background image

TX1330 M1

Upgrade and Maintenance Manual

111

Power supply

6.3.2.3

Installing the dummy cover

Figure 37: Installing the dummy cover

Ê

Insert the dummy cover into the empty bay with the impressed arrow symbol 
facing to the left (see circle).

Ê

Push the dummy cover into its bay until it locks in place.

V

CAUTION!

Always install dummy covers into unused bays to comply with 
applicable EMC regulations and satisfy cooling requirements.

6.3.3

Replacing a hot-plug power supply unit

V

CAUTION!

●

When replacing a power supply unit in a non-redundant PSU 
configuration, the server must be switched off first.

●

Ensure to replace a defective power supply unit by a new one of the 
same type.

Customer Replaceable Unit
(CRU)

Hardware: 5 minutes

Tools:

tool-less

Summary of Contents for Server PRIMERGY TX1330 M1

















































































































































































































































































































































Reviews:

No comments

Related manuals for Server PRIMERGY TX1330 M1

IBM BladeCenter HS22 Product Manual preview
BladeCenter HS22
Brand: IBM Pages: 18
Sybase Adaptive Server IQ 12.4.2 Administration And Performance Manual preview
Adaptive Server IQ 12.4.2
Brand: Sybase Pages: 536
NEC Express5800/320Fa-L User Manual preview
Express5800/320Fa-L
Brand: NEC Pages: 406
HMS Networks Anybus Communicator ABC4018 User Manual preview
Anybus Communicator ABC4018
Brand: HMS Networks Pages: 64
Supero SUPERO SuperServer 6026TT-H6IBQRF User Manual preview
SUPERO SuperServer 6026TT-H6IBQRF
Brand: Supero Pages: 110
7thSense M101-4 User Manual preview
M101-4
Brand: 7thSense Pages: 28
ORiNG IDS-5042 Series User Manual preview
IDS-5042 Series
Brand: ORiNG Pages: 67
Zonet ZPS3611 - QUICK Quick Installation Manual preview
ZPS3611 - QUICK
Brand: Zonet Pages: 1
IBM eServer xSeries 205 Type 8480 Hardware Maintenance Manual And Troubleshooting Manual preview
eServer xSeries 205 Type 8480
Brand: IBM Pages: 168
Acer Aspire EASYSTORE H341 Quick Start Manual preview
Aspire EASYSTORE H341
Brand: Acer Pages: 59
Acer Aspire EASYSTORE H341 Service Manual preview
Aspire EASYSTORE H341
Brand: Acer Pages: 74
Acer Aspire EasyStore Series User Manual preview
Aspire EasyStore Series
Brand: Acer Pages: 148
Acer Aspire easyStore H340 Service Manual preview
Aspire easyStore H340
Brand: Acer Pages: 68
Acer Altos EasyStore User Manual preview
Altos EasyStore
Brand: Acer Pages: 169
Acer Aspire easyStore H340 User Manual preview
Aspire easyStore H340
Brand: Acer Pages: 148
Acer Altos EasyStore Quick Installation Manual preview
Altos EasyStore
Brand: Acer Pages: 7
Dell PowerEdge 400SC Update preview
PowerEdge 400SC
Brand: Dell Pages: 1
Acer AR380 F2 Specifications preview
AR380 F2
Brand: Acer Pages: 20

Brands by name

Popular brands

Load more brands