Fujitsu Server PRIMERGY TX1330 M1 Upgrade And Maintenance Manual Download Page 152

Page: 152 / 336

152

Upgrade and Maintenance Manual

TX1330

System fan and air duct

Push the locking tab (2) inside while slightly lifting up the fan module to
disengage the retaining brackets on the server rear.

Lift the fan module out of the chassis (3).

8.2.3

Installing the fan module

Figure 70: Installing the fan module

Lower the fan module into the chassis.

Fit the four hooks on the fan module into the slots in the chassis (see blue
circles).

Press down on the fan module until the four hooks lock in the narrow ends
of the slots.

Ensure that the locking tab on the fan module is properly engaged with the
upper rim of the chassis (see orange circle).

Connect the fan cable to system board connector "FAN1 SYS" (see figure

Summary of Contents for Server PRIMERGY TX1330 M1

















































































































































































































































































































































Search results

Summary of Contents for Server PRIMERGY TX1330 M1

Reviews:

Fujitsu Server PRIMERGY TX1330 M1, Upgrade And Maintenance Manual, Page: 152 / 336

Search results

Summary of Contents for Server PRIMERGY TX1330 M1

Reviews: