manualshive.com logo in svg

Fujitsu Server PRIMERGY TX1330 M1, Upgrade And Maintenance Manual, Page: 160 / 336

Share
Download
Fujitsu Server PRIMERGY TX1330 M1 Upgrade And Maintenance Manual Download Page 160

160

Upgrade and Maintenance Manual

 TX1330 

M1

Expansion cards and backup units

9.1

Basic information

The system board is equipped with four expansion slots.

Figure 75: PCI slot overview

I

An additional PCI 32-bit slot is available with an optional riser card. This 
riser card can be mounted on two spacer bolts positioned under slot 1. In 
this case a PCI adapter board occupies slot 1 (see section 

"Installing the 

new riser card" on page 185

).

PCI slot Type 

Function

1

PCe Gen2 x1 
(mechanical x4)

slot for optional PCI adapter board (connected 
with riser card)

2

PCIe Gen 2 x4 
(mechanical x8)

3

PCIe Gen3 x8

4

PCIe Gen3 x8

dedicated slot for boot controllers

slot 4

slot 3

slot 2

slot 1

Summary of Contents for Server PRIMERGY TX1330 M1

















































































































































































































































































































































Reviews:

No comments