Fujitsu Server PRIMERGY TX1330 M1 Upgrade And Maintenance Manual Download Page 132

Page: 132 / 336

132

Upgrade and Maintenance Manual

TX1330

Hard disk drives / solid state drives

7.2.6.3

Installing the new 2.5-inch HDD SAS / SATA backplane

Figure 51: Installing the SAS / SATA backplane

At a slight angle, fit the SAS / SATA backplane into the two guides on the
drive cage (1).

Fold in the SAS / SATA backplane (2).

Secure the SAS / SATA backplane with the two screws (see figure

Connect all cables to the SAS / SATA backplane (see figure

For a complete cabling overview, please refer to section

"Cabling plans"

on page 303

7.2.6.4

Concluding steps

"Reassembling" on page 58

Reinstall all HDD / SSD modules to their original drive bays as described in
section

"Installing 2.5-inch HDD / SSD modules" on page 124

"Connecting the server to the mains" on page 67

"Switching on the server" on page 68

"Enabling BitLocker functionality" on page 90

Summary of Contents for Server PRIMERGY TX1330 M1

















































































































































































































































































































































Search results

Summary of Contents for Server PRIMERGY TX1330 M1

Reviews:

Fujitsu Server PRIMERGY TX1330 M1, Upgrade And Maintenance Manual, Page: 132 / 336

Search results

Summary of Contents for Server PRIMERGY TX1330 M1

Reviews: