Fujitsu Server PRIMERGY TX1330 M1 Upgrade And Maintenance Manual Download Page 126

Page: 126 / 336

126

Upgrade and Maintenance Manual

TX1330

Hard disk drives / solid state drives

7.2.3.4

Concluding steps

If applicable,

"Installing the HDD bay cover" on page 64

"Performing a RAID array rebuild" on page 90

7.2.4

Removing 2.5-inch HDD / SSD modules

7.2.4.1

Preliminary steps

If the HDD / SSD module to be removed is combined into a RAID array,
please proceed as follows:

Customer Replaceable Unit
(CRU)

Hardware: 5 minutes

Tools:

tool-less

RAID level

Procedure

RAID 0

Only remove an HDD module combined in a RAID 0 array if
defective.

CAUTION!

Removing an operational HDD module will result
in data loss!

RAID 1

RAID 5

Removing an HDD module from a RAID 1 or RAID 5 array
will not result in data loss.

However, the removed drive needs to be replaced
immediately by an HDD module of the same or larger
capacity.

After replacing the HDD module, RAID rebuild will
be performed as a background process as
described in section

"Performing a RAID array

rebuild" on page 90

Summary of Contents for Server PRIMERGY TX1330 M1

















































































































































































































































































































































Search results

Summary of Contents for Server PRIMERGY TX1330 M1

Reviews:

Fujitsu Server PRIMERGY TX1330 M1, Upgrade And Maintenance Manual, Page: 126 / 336

Search results

Summary of Contents for Server PRIMERGY TX1330 M1

Reviews: