Fujitsu Server PRIMERGY TX1330 M1 Upgrade And Maintenance Manual Download Page 179

Page: 179 / 336

TX1330 M1

Upgrade and Maintenance Manual

179

Expansion cards and backup units

"Connecting the server to the mains" on page 67

"Switching on the server" on page 68

"Updating RAID controller firmware" on page 80

If applicable,

"Enabling Option ROM scan" on page 81

"Enabling SVOM boot watchdog functionality" on page 84

"Enabling BitLocker functionality" on page 90

If applicable,

"After replacing / upgrading LAN controllers" on page 94

9.4.2

Removing expansion cards

9.4.2.1

Preliminary steps

"Disabling BitLocker functionality" on page 69

"Shutting down the server" on page 46

"Disconnecting the server from the mains" on page 46

Remove all external cables from the expansion card to be removed.

"Getting access to the component" on page 47

"Removing the fan module" on page 151

Upgrade and Repair Unit
(URU)

Hardware: 5 minutes

Tools:

tool-less

Summary of Contents for Server PRIMERGY TX1330 M1

















































































































































































































































































































































Search results

Summary of Contents for Server PRIMERGY TX1330 M1

Reviews:

Fujitsu Server PRIMERGY TX1330 M1, Upgrade And Maintenance Manual, Page: 179 / 336

Search results

Summary of Contents for Server PRIMERGY TX1330 M1

Reviews: