Fujitsu Server PRIMERGY TX1330 M1 Upgrade And Maintenance Manual Download Page 227

Page: 227 / 336

TX1330 M1

Upgrade and Maintenance Manual

227

Processors

11.2.7 Concluding steps

"Installing the fan module" on page 152

"Reassembling" on page 58

"Connecting the server to the mains" on page 67

"Switching on the server" on page 68

If applicable,

"Updating or recovering the system board BIOS and iRMC" on

page 76

"Enabling SVOM boot watchdog functionality" on page 84

"Enabling BitLocker functionality" on page 90

11.3

Replacing the processor heat sink

11.3.1 Preliminary steps

"Locating the defective server" on page 43

"Shutting down the server" on page 46

"Getting access to the component" on page 47

"Removing the fan module" on page 151

11.3.2 Replacing the processor heat sink

Remove the processor heat sink as described in section

"Removing the

processor heat sink" on page 219

Apply thermal paste to the processor surface as described in section

"Applying thermal paste" on page 223

Field Replaceable Unit
(FRU)

Hardware: 15 minutes

Tools:

Phillips PH2 / (+) No. 2 screw driver

Summary of Contents for Server PRIMERGY TX1330 M1

















































































































































































































































































































































Search results

Summary of Contents for Server PRIMERGY TX1330 M1

Reviews:

Fujitsu Server PRIMERGY TX1330 M1, Upgrade And Maintenance Manual, Page: 227 / 336

Search results

Summary of Contents for Server PRIMERGY TX1330 M1

Reviews: