manualshive.com logo in svg

Fujitsu Server PRIMERGY TX1330 M1, Upgrade And Maintenance Manual, Page: 46 / 336

Share
Download
Fujitsu Server PRIMERGY TX1330 M1 Upgrade And Maintenance Manual Download Page 46

46

Upgrade and Maintenance Manual

 TX1330 

M1

Basic hardware procedures

4.2

Shutting down the server

V

CAUTION!

For further safety information, please refer to chapter 

"Important 

information" on page 31

.

I

This step is only required when upgrading or replacing non-hot plug 
components.

Ê

Inform the system administrator that the server will be shut down and put 
offline.

Ê

Terminate all applications.

Ê

Perform the required procedures described in the preliminary steps of each 
upgrade or maintenance task.

Ê

Shut down the server.

I

If the system is running an ACPI-compliant operating system, 
pressing the On / Off button will perform a graceful shutdown.

Ê

Switch on the ID indicator on the front and rear connector panels of the 
server as described in section 

"Locating the defective server" on page 43

.

4.3

Disconnecting the server from the mains

Figure 2: Removing the power cord from the cable tie

Ê

Pull out on the locking lever on the cable tie (1) and loosen the loop (2).

Summary of Contents for Server PRIMERGY TX1330 M1

















































































































































































































































































































































Reviews:

No comments