Fujitsu Server PRIMERGY TX1330 M1 Upgrade And Maintenance Manual Download Page 299

Page: 299 / 336

TX1330 M1

Upgrade and Maintenance Manual

299

Converting a tower model to a rack model

Firmly press down on the rack mounting bracket until it is fully seated in the
rack front bezel (2).

Mount the second rack mounting bracket accordingly.

Figure 201: Installing accessible drive dummy covers

If available, reinstall all accessible drive dummy covers into their original
locations (rotated by 90 degrees):

Ensure that an accessible drive filler cover has been installed in every
empty drive bay.

Turn the front cover face down.

Join the two lugs on one edge of the accessible drive cover with the right
inner edge of the front cover (1).

Fold down the accessible drive cover until it snaps in place (2).

Use the dummy covers that have been removed from the front cover
during the preliminary steps.

Install the rack front cover as described in section

"Installing the rack front

cover" on page 58

Summary of Contents for Server PRIMERGY TX1330 M1

















































































































































































































































































































































Search results

Summary of Contents for Server PRIMERGY TX1330 M1

Reviews:

Fujitsu Server PRIMERGY TX1330 M1, Upgrade And Maintenance Manual, Page: 299 / 336

Search results

Summary of Contents for Server PRIMERGY TX1330 M1

Reviews: