Fujitsu Server PRIMERGY TX1330 M1 Upgrade And Maintenance Manual Download Page 240

Page: 240 / 336

240

Upgrade and Maintenance Manual

TX1330

Accessible drives

Figure 150: Front panel with USB 3.0 cable for connecting RDX backup drives

Use the connector marked with the circle for the connection of the RDX
backup drive.

Notes on RDX backup drive USB cabling:

– A USB 2.0 RDX drive may be replaced by a USB 3.0 RDX drive with

previous cabling.

– A USB 3.0 RDX drive may be connected with a USB 2.0 cable to the

onboard USB 2.0 connector with limited performance.

– The USB 3.0 cable cannot be connected to a USB 2.0 RDX drive.

12.2.6 Concluding steps

"Installing the rack front cover" on page 58

(rack server) or

"Installing the

front cover" on page 63

(tower server)

"Reassembling" on page 58

"Connecting the server to the mains" on page 67

"Switching on the server" on page 68

If applicable,

"Verifying and configuring the backup software solution" on

page 81

"Enabling BitLocker functionality" on page 90

Summary of Contents for Server PRIMERGY TX1330 M1

















































































































































































































































































































































Search results

Summary of Contents for Server PRIMERGY TX1330 M1

Reviews:

Related manuals for Server PRIMERGY TX1330 M1

Brands by name

Popular brands

Fujitsu Server PRIMERGY TX1330 M1, Upgrade And Maintenance Manual

Search results

Summary of Contents for Server PRIMERGY TX1330 M1

Reviews:

Related manuals for Server PRIMERGY TX1330 M1

Brands by name

Popular brands