manualshive.com logo in svg

Fujitsu Server PRIMERGY TX1330 M1, Upgrade And Maintenance Manual

The Fujitsu Server PRIMERGY TX1330 M1 is a high-performance server offering exceptional reliability and scalability. Ensure efficient operation and optimize performance with the Upgrade and Maintenance Manual, available for free download from our website. This comprehensive manual provides valuable insights and step-by-step instructions, enabling users to successfully maintain and upgrade their server.

Share
Download
background image

TX1330 M1

Upgrade and Maintenance Manual

133

Hard disk drives / solid state drives

7.3

3.5-inch HDD configurations

7.3.1

Mounting order

Maximum configuration: 4x 3.5-inch HDDs

Figure 52: 3.5-inch HDD mounting order (example tower server)

7.3.2

HDD naming scheme

7.3.3

Installing 3.5-inch HDD modules

3.5-inch HDDs

Bay

RAID 

Manager 

#

Channel

log. 

Drive #

Bay

RAID 

Manager 

#

Channel

log. 

Drive #

1

[0]

1

0

3

[2]

1

2

2

[1]

1

1

4

[3]

1

3

Table 5: HDD naming scheme

Customer Replaceable Unit
(CRU)

Hardware: 5 minutes

Summary of Contents for Server PRIMERGY TX1330 M1

















































































































































































































































































































































Reviews:

No comments

Related manuals for Server PRIMERGY TX1330 M1

NEC Express5800/T110g-S Configuration Manual preview
Express5800/T110g-S
Brand: NEC Pages: 34
Sun Microsystems Netra ft 1800 Installation Manual preview
Netra ft 1800
Brand: Sun Microsystems Pages: 90
360 Systems MAXX-1200-HD Operation Manual preview
MAXX-1200-HD
Brand: 360 Systems Pages: 148
Artesyn AXP640 Installation And Use Manual preview
AXP640
Brand: Artesyn Pages: 190
Supero SuperServer 6026TT-HIBQF User Manual preview
SuperServer 6026TT-HIBQF
Brand: Supero Pages: 112
Fujitsu PRIMERGY Econel 230R S1 Service Supplement Manual preview
PRIMERGY Econel 230R S1
Brand: Fujitsu Pages: 53
Fujitsu Primergy ECONEL 100 S2 Start Manual preview
Primergy ECONEL 100 S2
Brand: Fujitsu Pages: 8
Fujitsu PRIMERGY Econel 200 S2 Options Manual preview
PRIMERGY Econel 200 S2
Brand: Fujitsu Pages: 65
Fujitsu PRIMERGY MX130 S1 Operating Manual preview
PRIMERGY MX130 S1
Brand: Fujitsu Pages: 85
Fujitsu PRIMERGY Econel 100 Operating Manual preview
PRIMERGY Econel 100
Brand: Fujitsu Pages: 64
Fujitsu primergy h250 Manual preview
primergy h250
Brand: Fujitsu Pages: 105
Fujitsu Primergy N800 Manual preview
Primergy N800
Brand: Fujitsu Pages: 142
Fujitsu PRIMERGY GX2460 M1 Upgrade And Maintenance Manual preview
PRIMERGY GX2460 M1
Brand: Fujitsu Pages: 251
Fujitsu PRIMERGY MX130 S2 Upgrade and maintenance manua Upgrade And Maintenance Manual preview
PRIMERGY MX130 S2 Upgrade and maintenance manua
Brand: Fujitsu Pages: 256
Fujitsu Primergy RX100 S2 User Manual preview
Primergy RX100 S2
Brand: Fujitsu Pages: 275
Fujitsu Primergy RX100 S3 User Manual preview
Primergy RX100 S3
Brand: Fujitsu Pages: 287
Fujitsu PRIMERGY ECONEL30 Configuration Manual preview
PRIMERGY ECONEL30
Brand: Fujitsu Pages: 11
Brother RuggedJet RJ-4040 Software Manual preview
RuggedJet RJ-4040
Brand: Brother Pages: 111

Brands by name

Popular brands

Load more brands