manualshive.com logo in svg

Fujitsu Server PRIMERGY TX1330 M1, Upgrade And Maintenance Manual, Page: 184 / 336

Share
Download
Fujitsu Server PRIMERGY TX1330 M1 Upgrade And Maintenance Manual Download Page 184

184

Upgrade and Maintenance Manual

 TX1330 

M1

Expansion cards and backup units

Ê

If applicable, reconfigure your network settings in the operation system 
according to the original configuration of the replaced controller (expansion 
card or onboard).

I

Configuration of network settings should be performed by the 
customer. 

For further information, please refer to section 

"Note on network 

settings recovery" on page 182

.

Ê

If applicable, 

"After replacing / upgrading LAN controllers" on page 94

9.4.4

Replacing the riser card

9.4.4.1

Preliminary steps

Ê

"Locating the defective server" on page 43

Ê

"Disabling BitLocker functionality" on page 69

Ê

"Shutting down the server" on page 46

Ê

"Disconnecting the server from the mains" on page 46

Ê

Remove all external cables from the expansion card installed in the riser 
card slot.

Ê

"Getting access to the component" on page 47

Ê

"Removing the fan module" on page 151

9.4.4.2

Removing the defective riser card

Ê

Remove the expansion card from the riser card slot as described in section 

"Removing an expansion card" on page 180

.

Upgrade and Repair Unit
(URU)

Hardware: 5 minutes

Tools:

Phillips PH2 / (+) No. 2 screw driver

Summary of Contents for Server PRIMERGY TX1330 M1

















































































































































































































































































































































Reviews:

No comments