Fujitsu Server PRIMERGY TX1330 M1 Upgrade And Maintenance Manual Download Page 254

Page: 254 / 336

254

Upgrade and Maintenance Manual

TX1330

System board and components

14.2 Replacing the CMOS battery

Safety notes

CAUTION!

●

The CMOS battery must be replaced with an identical battery or with
a battery type recommended by the manufacturer.

●

Keep lithium batteries away from children.

●

Do not throw batteries into the trash can. Lithium batteries must be
disposed of in accordance with local regulations concerning special
waste.

●

For further safety information, please refer to section "Environmental
protection" in the operating manual of your server.

●

Ensure to insert the CMOS battery the with the positive pole
facing up!

14.2.1 Preliminary steps

"Locating the defective server" on page 43

"Shutting down the server" on page 46

"Disconnecting the server from the mains" on page 46

"Getting access to the component" on page 47

Upgrade and Repair Unit
(URU)

Hardware: 5 minutes

Tools:

tool-less; recommended: tooth pick

Summary of Contents for Server PRIMERGY TX1330 M1

















































































































































































































































































































































Search results

Summary of Contents for Server PRIMERGY TX1330 M1

Reviews:

Fujitsu Server PRIMERGY TX1330 M1, Upgrade And Maintenance Manual, Page: 254 / 336

Search results

Summary of Contents for Server PRIMERGY TX1330 M1

Reviews: