Fujitsu Server PRIMERGY TX1330 M1 Upgrade And Maintenance Manual Download Page 173

Page: 173 / 336

TX1330 M1

Upgrade and Maintenance Manual

173

Expansion cards and backup units

Figure 94: Removing the protective optical port plug

If present, remove the protective optical port plug from the SFP+ transceiver
module.

CAUTION!

Save the protective port plug for future use.

Figure 95: Unlatching the locking bail

Carefully unlatch and fold down the locking bail on the SFP+ transceiver
module to eject the transceiver from the socket connector.

Summary of Contents for Server PRIMERGY TX1330 M1

















































































































































































































































































































































Search results

Summary of Contents for Server PRIMERGY TX1330 M1

Reviews:

Related manuals for Server PRIMERGY TX1330 M1

Brands by name

Popular brands

Fujitsu Server PRIMERGY TX1330 M1, Upgrade And Maintenance Manual

Search results

Summary of Contents for Server PRIMERGY TX1330 M1

Reviews:

Related manuals for Server PRIMERGY TX1330 M1

Brands by name

Popular brands