Fujitsu Server PRIMERGY TX1330 M1 Upgrade And Maintenance Manual Download Page 183

Page: 183 / 336

TX1330 M1

Upgrade and Maintenance Manual

183

Expansion cards and backup units

9.4.3.2

Removing the defective expansion card

If applicable, remove SFP+ transceiver modules from the expansion card to
be removed, as described in section

"Removing an SFP+ transceiver

module" on page 172

Remove the expansion card as described in section

"Removing expansion

cards" on page 179

If the slot bracket on the defective expansion card is to be reused, remove it
from the board as described in section

"Removing a slot bracket" on

page 168

9.4.3.3

Installing the new expansion card

If applicable, install a slot bracket on the expansion card as described in
section

"Installing a slot bracket" on page 162

Install the expansion card as described in section

"Installing expansion

cards" on page 175

If applicable, reinstall SFP+ transceiver modules on the expansion card, as
described in section

"Installing SFP+ transceiver modules" on page 169

9.4.3.4

Concluding steps

"Installing the fan module" on page 152

"Reassembling" on page 58

Reconnect all external cables to the replaced expansion card.

"Connecting the server to the mains" on page 67

"Switching on the server" on page 68

"Enabling replaced components in the system BIOS" on page 85

Inform the customer about changed WWN and MAC addresses. For further
information, refer to section

"Looking up changed MAC / WWN addresses"

on page 91

"Updating the NIC configuration file in a Linux environment" on page 88

"Updating RAID controller firmware" on page 80

"Enabling SVOM boot watchdog functionality" on page 84

"Enabling BitLocker functionality" on page 90

Summary of Contents for Server PRIMERGY TX1330 M1

















































































































































































































































































































































Search results

Summary of Contents for Server PRIMERGY TX1330 M1

Reviews:

Fujitsu Server PRIMERGY TX1330 M1, Upgrade And Maintenance Manual, Page: 183 / 336

Search results

Summary of Contents for Server PRIMERGY TX1330 M1

Reviews: