Fujitsu Server PRIMERGY TX1330 M1 Upgrade And Maintenance Manual Download Page 62 | Manualshive

Page: 62 / 336

background image

62

Upgrade and Maintenance Manual

TX1330

M1

Basic hardware procedures

4.5.1.4

Sliding the server into the rack

Figure 17: Sliding the server into the rack

Ê

Pull up on the locking latch on both telescopic rails (1).

Ê

Slide the server inside the rack as far as it will go (2) until the quick release
levers lock into place.

Ê

Reconnect all cables except the power cord to the server rear.

I

If you are not using a cable mounting arm (CMA kit), ensure that the
rear cables are long enough not to be strained or damaged when
extending the server out of the rack.
Use cable ties to prevent loose cables from blocking the air flow.

«
...
60
61
62
63
64
...
»

Summary of Contents for Server PRIMERGY TX1330 M1

















































































































































































































































































































































Reviews:

No comments

Related manuals for Server PRIMERGY TX1330 M1

Express5800/320Fa-L

Brand: NEC Pages: 406

Brand: IBM Pages: 82

SuperServer 1029U-T Series

Brand: Supermicro Pages: 1

SMAVIA DMS 2400 II

Brand: dallmeier Pages: 36

PRIMERGY TX140 S2

Brand: Fujitsu Pages: 86

PRIMERGY TX150 S3

Brand: Fujitsu Pages: 95

PRIMERGY TX150 S6

Brand: Fujitsu Pages: 118

Brand: Fujitsu Pages: 305

PRIMERGY TX150 S6

Brand: Fujitsu Pages: 127

PRIMERGY TX140 S2

Brand: Fujitsu Pages: 332

PRIMERGY TX150 S4

Brand: Fujitsu Pages: 97

PRIMERGY TX150 S7

Brand: Fujitsu Pages: 120

PRIMERGY TX140 S1p

Brand: Fujitsu Pages: 9

2622W-P - annexe 1

Brand: SMC Networks Pages: 83

Brand: PCI Pages: 87

Brand: BCDVideo Pages: 157

ZXCLOUD iBox CT220

Brand: Zte Pages: 16

Brand: NuPrime Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands