Foma PushTalk SH902i, Manual

Page: 331 / 568

329
i-
a
pp
li
i-
a
pp
li To
Fu
n
c
tion
If i-
a
ppli To (Run i-
a
ppli) is displayed in a site,
Internet web page, i-mode mail or screen
memo, i-
a
ppli can be started. i-
a
ppli also
starts when a signal to start i- a ppli is received
during Ir exchange, when the start signal is
read by the Bar code reader or when the
FeliCa mark is held up to the reader/writer
(external device) and the start signal is read.
Set whether to allow i-
α
ppli To in i-
α
ppli To settings.
Select whether to start i-
α
ppli with i-
α
ppli To for
each software.
i-
α
ppli To is set to Yes when software is downloaded.
The default setting is Yes .
1
In the software list (
n
P. 322),
select software and press
C6
[Set software use].
2
Select i-
a
ppli To , press
t
and
press
1
[Yes].
3
Press
i
[Complete].
If i-
α
ppli To (Run i-
α
ppli) is set for a site, Internet
web page, i-mode mail or screen memo, i-
α
ppli
can be started. Or, start i-
α
ppli by holding the
FeliCa mark up to a reader/writer (external
device) to read Run i-
α
ppli information.
If i-
α
ppli To is set to No , i-
α
ppli does not function.
Cannot be activated as i-
α
ppli stand-by.
Full Browser is not available.
1
Select i-
a
ppli in a site, Internet web
page, i-mode mail or screen memo,
press
t
, select Yes and press
t
.
The software starts.
To cancel, press
H
while i- a ppli activating
appears.
Set i- a ppli as the stand-by display.
Press
c
to operate i-
α
ppli set as the stand-by display.
Set whether to transmit from the software set as the i-
α
ppli
stand-by, using Stand-by NW set (
n
P. 330).
1
In the software list (
n
P. 322), select
software, press
C4
[Stand-by
display], select Yes and press
t
.
The software is set as
i-
α
ppli stand-by, and
the software starts
when the stand-by
display reappears.
The screen shown on the above right appears
when the software uses transmission. Select
Yes to allow transmission.
When No is selected, data is not transmitted
and information may not be received.
i-
a
ppli To Function
Running i-
a
ppli from Sites or
i-mode Mail
Configuring Startup with i-
a
ppli To
<i-
a
ppli To>
Note
The software to start is determined by the site,
Internet web page, i-mode mail or screen memo.
Download the specified software in advance.
Starting i-
a
ppli from Sites or i-mode
Mail
<i- a ppli To Function>
Note
When i-
α
ppli is ended, the original site, Internet
web page, received message screen or screen
memo reappears.
If there is no software corresponding to the Run i-
α
ppli
setting, No requested software appears.
Some software run from a site cannot be saved on
the FOMA terminal.
Depending on the site, the specified i-
α
ppli software
can be downloaded if it is not saved on the FOMA
terminal or if a newer version is available for the
software saved on the FOMA terminal.
Depending on the software settings, the software may
start automatically after downloading is complete. In
such cases, i-
α
ppli screen closes and the software
cannot be saved to the FOMA terminal immediately
after downloading. After ending the software, select
whether to save it.
Network set (
n
P. 323) may be required while
running i-
α
ppli software.
i-
α
ppli To from i-mode mail is a function only
available from i-mode mail delivered from an IP
(Information Provider). Not available for i-mode
mail exchanged between FOMA terminals.
i-
a
ppli Stand-by
Setting i-
a
ppli as the Stand-by
Display
Setting i-
a
ppli as the Stand-by Display
<Stand-by Display>
Note
Only one software can be set as i-
α
ppli stand-by.
Some software cannot be set as i-
α
ppli stand-by.
dv30̲e.book Page 329 Tuesday, November 22, 2005 3:21 PM