18
eSuspension manufacturer. eSuspension is only
available in combination with the Kiox on-board
computer and can only be used with the BDU450
CX, BDU480 CX and BDU490P drive units.
ABS – anti-lock braking system (optional)
If the wheel is fitted with a Bosch e-bike ABS with
no external control lights, the control lights will be
shown on the display when the system starts and
in the event of a fault. For detailed information on
the ABS and how it works, please refer to the ABS
operating instructions.
Lock (premium function)
You can buy this function from the
<Shop>
in the
e-bike Connect app. Once the Lock function is
switched on, the e-bike drive unit assistance is
deactivated. It can only then be activated using
the on-board computer associated with the e-bike.
Detailed operating instructions can be found on-
line at
www.Bosch-e-bike.com/Kiox-manual.
Software updates
Software updates are transferred to the on-board
computer in the background of the app as soon
as it is connected to the app. When an update
is complete, this will be displayed the next three
times the on-board computer is restarted.
Alternatively, you can check in the
<Sys set
-
tings>
whether an update is available.
Powering external devices via the USB port
The USB port can be used to operate or charge
most devices that can be powered via USB (e.g.
various mobile phones). Charging requires the
on-board computer to be mounted
and a sufficiently charged battery to be inserted
in the e-bike.
Open the protective cover
(17)
for the USB port
on the on- board computer. Use a Micro-A – Mi-
cro-B USB charging cable (available from your
Bosch e-bike dealer) to connect the USB port on
the external device to the USB port
(6)
on the on-
board computer.
Once the electrical load has been disconnected,
the USB port must be carefully resealed with the
protective cover
(17).
USB connections are not
waterproof. When cycling in the rain, do not con-
nect any external devices and make sure that the
USB port is fully sealed by the protective cover
(17).
Important: If electrical loads are connected,
this can affect the range of the e-bike.
Displays and settings of the on-board computer
Please note: All screenshots showing the display
and text on the following pages are from the ap
-
proved software version. The display and/or text
may change slightly following a software update.
If the on-board computer is removed from the
holder
(5),
the assistance level that was last dis-
played for the battery is saved.
Switching the push assistance on/off
The push assistance aids you when pushing your
e-bike. The speed in this function depends on the
selected gear and can reach a maximum of 6 km/h.
The lower the selected gear, the lower the speed of
the push assistance function (at full power).
• The push assistance function must only be
used when pushing the e-bike. There is a risk
of injury if the wheels of the e-bike are not in
contact with the ground while using the push
assistance.
To activate the push assistance, briefly press the
WALK button on your on-board computer. After
activation, press the + button within 3 s and keep
it pressed. The e-bike drive is switched on.
Note: The push assistance cannot be activated at
assistance level OFF.
The push assistance is switched off as soon as
one of the following occurs:
– You release the + button;
– The wheels of the e-bike are locked (e.g. by ap-
plying the brakes or hitting an obstacle);
–
The speed exceeds 6 km/h.
The push assistance function is subject to local
regulations; the way it works may therefore differ
from the description above, or the function may
even be deactivated completely.
Switching bicycle lights on/off
On the model in which the lighting is powered by
the e-bike system, the front and rear lights can
be switched on and off at the same time via the
on-board computer using the bike light button (3).
With the light switched on, the lighting c indicator
(see “Start page”, page English – 19) appears in
the status bar on the display.
Switching the bike lights on and off has no effect
on the backlighting of the display.
eShift (optional)
eShift is the integration of electronic gear-shifting
systems into the e-bike system. The eShift com-
ponents are electrically connected to the drive
unit by the manufacturer. The separate operating
instructions describe how to operate the electron-
ic gear-shifting systems.
eSuspension (optional)
eSuspension is the integration of electronic shock
absorption and suspension elements into the e-bike
system. You can use the Quick Menu to select pre-
defined settings for the eSuspension system.
For details of these settings, please refer to
the operating instructions provided by the
Summary of Contents for Goroc 3
Page 53: ...FR FLYER Mountain Bosch fr Traduction de la notice originale EN 15194...
Page 104: ...IT IT FLYER Mountain Bosch it Traduzione delle istruzioni originali EN 15194...
Page 155: ...EN EN FLYER Mountain Bosch en Translation of the original instruction manual EN 15194...
Page 203: ...NL NL FLYER Mountain Bosch nl Vertaling van de originele gebruiksaanwijzing EN 15194...
