Flyer Goroc 3, Translation Of The Original Instruction Manual

Page: 167 / 252

14
The version information for the subsystems can
be checked for maintenance purposes. With the
system switched off, press the «–» and «+» but-
tons simultaneously, then press the on/off button
1 .
The USB socket is reserved for connection to di-
agnostic systems. It has no other function.
English – 4​
1 270 020 XBP | (11.02.2019) Bosch eBike Systems
Displays and configurations of the
on-board computer
Battery charge indicator
The battery charge indicator (g) displays the eBike battery's
state of charge. The state of charge of the eBike battery can
also be checked on the LEDs of the battery itself.
In the indicator (g), each bar in the battery symbol repres-
ents approximately 20 % capacity:
The eBike battery is fully charged.
The eBike battery should be recharged.
The LEDs of the battery charge indicator on the
battery go out. The capacity for assisting the drive
has been used up, and assistance is gently
switched off. The remaining capacity is made
available for the lighting. The indicator flashes.
The capacity of the eBike battery is enough for
about two hours of lighting.
Speed and distance indicators
The speedometer (a) always displays the current speed.
Indicator (i) always displays the last setting as standard. Re-
peated medium-length presses of the button – will display
the trip distance TRIP, the total distance TOTAL and the
range of the battery RANGE one after the other. (Briefly
pressing the button – will decrease the assistance level.)
To reset the trip distance TRIP, select the trip distance TRIP
and simultaneously press and hold the buttons + and –.
The display will initially show RESET. If you continue to press
both buttons, the trip distance TRIP will be set to 0.
To reset the range of the battery RANGE, select the battery
range RANGE and simultaneously press and hold the but-
tons + and –. The display will initially show RESET. If you
continue to press both buttons, the trip distance TRIP will be
set to 0.
You can switch the displayed values from kilometres to miles
by holding down the button – and briefly pressing the
on/off button (1).
The versions of the subsystems and their model part num-
bers can be displayed for the purposes of servicing,
provided the subsystems divulge this information (depend-
ent on the subsystem). With the system switched off, simul-
taneously press the buttons – and + and then press the on/
off button (1).
The USB port is reserved for connecting diagnostic systems.
The USB port does not have any other function.
u
The USB connection must always be completely
sealed with the protective cap (8).
Action Buttons Duration
Switch on on-board computer Any
Switch off on-board computer Any
Increase assistance +
Decrease assistance –
Display TRIP, TOTAL, RANGE,
assistance modes
–
Switch on bike lights
+
Switch off bike lights +
Reset trip distance – +
Activate push assistance
Implement push assistance
WALK
+
1.
2. Any
Switch from kilometres to miles – 1. Keep
pressed
2.
Display the versions A)B) – + 1. Keep
pressed
2.
Adjust display brightness C) – +
– or +
1. Keep
pressed
2.
A) The eBike system must be switched off.
B) The information is shown as scrolling text.
C) The display must be switched off.
The USB connection must always be
fully closed with the protective cover 8.
Error code display
Continuous monitoring of the components of the
FLYER e-bike system is carried out automat-
ically. If an error is detected, the corresponding
error code appears on the on-board computer.
Depending on the error type, the motor may be
switched off automatically. However, you can con -
tinue to ride without motor assistance at all times.
The e-bike must be checked before being ridden
again.
The list of error codes can be found in the sepa-
rate Purion operating instructions.
All repairs must be carried out by an au-
thorised bicycle retailer.
The full range of assistance levels includes:
• OFF : motor assistance is switched off; the E-bike
is operated like a normal bicycle through pedalling
alone. The pushing aid cannot be activated in this
assistance level.
• ECO : effective assistance with optimum efficiency
for maximum range.
• TOUR : consistent levels of assistance for tours
with large ranges.
SPORT/eMTB :
• SPORT : powerful assistance for active riding on
hilly terrain and in city traffic.
• eMTB : optimum assistance on any terrain, fast
acceleration, improved dynamics, maximum per -
formance
• TURBO : maximum assistance up to high pedalling
frequencies for active riding
To increase the support level, briefly press the
«+» 6 button on the on-board computer until the
desired support level appears on the display
i.
Press the «–» 5 button to decrease the support
level.
Switch bicycle lighting on/off
For models where the headlight is powered by the
E-bike system, you can switch on the front and
rear lights simultaneously by pressing the «+»
button for a couple of seconds . Hold down
«+» button to switch off the bicycle lights.
When the lights are switched on, the lighting sym-
bol h is displayed.
Switching the bicycle lighting on and off does not
affect the display backlight.
Indicators and settings on the on-board com-
puter:
speed and distance indicators
The speedometer display a always shows the
current speed.
In the standard configuration, the display i always
shows the last setting. If you repeatedly press the
«–» button for a couple of seconds , the travel
distance
«TRIP»
, total kilometres
«TOTAL»
and
battery range «RANGE» are displayed in succes-
sion. (Briefly pressing pressing the «–» button
decreases the support level!)
To reset the travel distance «TRIP» , press and
hold the «+» and «–» buttons simultaneously.
First, «RESET» appears on the display. Continue
to hold down both buttons to reset the travel dis-
tance «TRIP» to “0” .
To change the displayed values from kilometres
to miles, hold down and press the on/off but -
ton
1.