manualshive.com logo in svg

Ferrari 458 Spider, Owner'S Manual

The Ferrari 458 Spider Owner's Manual is a comprehensive guide that provides essential information on operating and maintaining this iconic sports car. Downloadable for free from manualshive.com, this manual is a must-have for every Ferrari enthusiast, offering detailed instructions and insights to enhance your driving experience.

Share
Download
background image

77

3

Safety

If an event occurs that needs to be displayed as a symbol and/or 

special message when the TYRES screen page is displayed, the 

screen page is minimised as shown in example 

2

. For further 

information, refer to the “Fault displaying logic” paragraph on 

page 113.

 Low pressure

Regardless of the type of screen page on the left TFT display, when 

the instrument panel receives the signal from the tyre pressure 

ECU that the pressure level of one or more tyres is below the alarm 

threshold, the screen page shown in example 

3

 (for a warning 

related to only one tyre) or example 

4

 (for a warning related to 

several tyres) appears immediately.

The screen page is displayed for 20 seconds and then the screen 

page that was previously displayed reappears. If the failure 

persists, the screen page shown above (example 

3

 or 

4

) will be 

automatically displayed for 20 seconds the next time the engine is 

started.
The driver can call up the TYRES screen page at any time to 

display which tyres have low pressure (example 

5

).

Catalysts temp.

too high

Engine

performance

limited

2

Check tyre

pressure

3

Check tyre

pressure

4

5

Summary of Contents for 458 Spider





































































































































































































































































Reviews:

No comments

Related manuals for 458 Spider

HALE MM-03 Driver Manual preview
MM-03
Brand: HALE Pages: 44
RAM Commercial PROMASTER 2020 Quick Reference Manual preview
PROMASTER 2020
Brand: RAM Commercial Pages: 12
Pacbrake C44059 Installation Manual preview
C44059
Brand: Pacbrake Pages: 14
RAM 2011 DAKOTA User Manual preview
2011 DAKOTA
Brand: RAM Pages: 76
Advantech TREK-550 Manual preview
TREK-550
Brand: Advantech Pages: 59
Honda 2010 Civic Sedan Owner'S Manual preview
2010 Civic Sedan
Brand: Honda Pages: 390
U.S. General 96524 Set Up And Operating Instructions Manual preview
96524
Brand: U.S. General Pages: 8
E&G Classics 1409-0102-10 Installation Instructions preview
1409-0102-10
Brand: E&G Classics Pages: 3
Black+Decker BXAE00011 Operating Instructions Manual preview
BXAE00011
Brand: Black+Decker Pages: 21
Beeper RW050RF User& Installer'S Manual preview
RW050RF
Brand: Beeper Pages: 20
Jeep CHEROKEE 2017 User Manual preview
CHEROKEE 2017
Brand: Jeep Pages: 374
Ford Focus 2008 Quick Reference Manual preview
Focus 2008
Brand: Ford Pages: 2
Mobileye C2-270 User Manual preview
C2-270
Brand: Mobileye Pages: 29
EUFAB 12014 Manual preview
12014
Brand: EUFAB Pages: 20
Audiovox Prestige 128-8602 Installation Manual preview
Prestige 128-8602
Brand: Audiovox Pages: 8
Goobay KFZ 112 Quick Start Manual preview
KFZ 112
Brand: Goobay Pages: 2
Nos 05183NOS Owner'S Manual preview
05183NOS
Brand: Nos Pages: 22
Dodge 2008 Dakota Owner'S Manual preview
2008 Dakota
Brand: Dodge Pages: 439

Brands by name

Popular brands

Load more brands