Ferrari 458 Spider Owner'S Manual Download Page 169

Page: 169 / 260

169

About your Vehicle

Stop&Start

active

Important note

Each time the ignition key is turned to position

(Key-on), the

Stop&Start system remains in the same state it was in when the

switch was turned to position

(Key-off). If the function was

activated at Key-off, it remains activated at the next Key-on and

the LED on button

will ﬂ ash for a few seconds.

Automatic engine stop mode

The engine stops automatically when the vehicle is stationary

and the brake pedal is pressed and restarts when the brake

pedal is released.

The left TFT display informs the driver that the Stop&Start system

has been activated by displaying the message “Stop&Start active”

accompanied by a special symbol. The message is displayed as long

as the vehicle remains in a stop state. To interrupt the display cycle

and reduce the message to an icon, press the

MODE

button with

“ESCAPE” function.

Summary of Contents for 458 Spider





































































































































































































































































Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands

Ferrari 458 Spider, Owner'S Manual

Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands