Ferrari 458 Spider Owner'S Manual Download Page 168

Page: 168 / 260

168

About your Vehicle

How the system works

If activated, the Stop&Start system decides when to switch off the

engine and when to restart it according to the driving conditions,

the climate comfort on board and the operating status of the

vehicle. The system logic does not require drivers to make any

change in the way they drive the vehicle.

Manual activation and deactivation button

The driver can activate/deactivate the Stop&Start system at

any time by pressing button

on the roof panel. If the system

is activated, pressing button

will deactivate it: the message

“Stop&Start OFF” appears for 5 seconds on the left TFT display

accompanied by a special symbol.
Once the system has been deactivated, pressing button

again

reactivates the system: the message “Stop&Start ON” appears for

5 seconds on the left TFT display accompanied by a special symbol.

If the Stop&Start system is activated, the LED on button

comes

on whereas if the system is deactivated, the LED goes off.
Deactivation of the system by pressing button

while in a stopped

vehicle condition (when the engine has been automatically

switched off by the Stop&Start function) automatically restarts the

engine.

Stop&Start

OFF

Summary of Contents for 458 Spider





































































































































































































































































Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands

Ferrari 458 Spider, Owner'S Manual

Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands