Ferrari 458 Spider Owner'S Manual Download Page 211

Page: 211 / 260

211

Advice for Emergency Situations

Warning

While towing the vehicle, you must comply with Road

Regulations.

Warning

Do not tow the vehicle by attaching to levers, suspension and

wheel rims but only to the tow hook properly ﬁtted in place.
Keep the key in position

to enable the lights to work and

prevent the steering wheel from locking if it is turned; when

towing the vehicle, do not start the engine.

Important note

Remember that when the engine is switched off, the power

steering and brake servo functions do not work.

Fuel inertia switch

The fuel inertia switch is a safety device which deactivates the fuel

pump relays if a collision occurs.
A symbol appears on the left TFT display and the hazard warning

lights come on to indicate that the switch has been activated.
When the fuel inertia switch is activated, the doors are also

unlocked (if locked) and the central dome light comes on.

Warning

The fuel pump relays can be reactivated by pressing the button

in the battery compartment which can be accessed by opening

the passenger side footrest.

Summary of Contents for 458 Spider





































































































































































































































































Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands

Ferrari 458 Spider, Owner'S Manual

Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands