Ferrari 458 Spider Owner'S Manual Download Page 194

Page: 194 / 260

194

Advice for Emergency Situations

Emergency tyre repair and inﬂation kit

Stored in the luggage compartment, it can be used in the event of a

puncture or low tyre pressure to repair and/or inﬂate a tyre enough

to continue the journey safely.

Important note

To use the tyre repair and inﬂation kit correctly, refer to the

instruction booklet supplied with the kit.

Warning

Give the instruction manual supplied with the kit to the

personnel that will handle the tyre repaired with the tyre repair

kit.

Warning

In the event of a puncture caused by foreign objects, tyres can

be repaired with cuts of up to

4 mm

in diameter on the tyre

tread and shoulder.

Warning

Punctures cannot be repaired on the sides of the tyre. Do not

use the tyre repair kit if the tyre has been damaged after driving

with a ﬂat tyre.

Warning

Damage to the wheel rim that causes air leaks cannot be

repaired. Do not remove foreign objects (screws or nails) that

have penetrated the tyre.

Warning

After using the repair kit, the vehicle must be considered in an

emergency situation: drive with the greatest care (maximum

permissible speed 80 km/h - 50 mph).

Warning

Apply the sticker supplied with the kit where it can easily be

seen by the driver to indicate that the tyre has been treated with

the tyre repair kit.
Drive carefully especially on bends.
Avoid sudden accelerations or braking.

Warning

The kit is to be used to temporarily repair only one tyre

punctured by small objects: the kit may not be useful in the case

of large punctures or tearing.

Summary of Contents for 458 Spider





































































































































































































































































Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands

Ferrari 458 Spider, Owner'S Manual

Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands