Ferrari 458 Spider Owner'S Manual Download Page 105

Page: 105 / 260

105

About your Vehicle

ESC Autolearning

Function not available

After each start, the ESC stability and traction control system

compensates for the tyre rolling radius and detects the spare

wheel. While this procedure is being performed, the Vehicle Status

screen page indicates to the driver that system self-acquisition is in

progress by displaying the message “ESC autolearning”.

Warning

Use of the vehicle on race tracks: after each start, cover the ﬁ rst

straight stretch of the track (at least 500 meters / 0.3 mi) at a

constant speed so that the ESC stability and traction control

system can calculate exactly the grip available and the rolling

radius of the tyres (the calculation is reset every time the engine

stops).
If this rule is not followed, system performance may be reduced.

If one or more signals related to the performance parameters used

to calculate the thermal state of the subsystems (lateral acceleration,

speed, etc.) are not valid, the Vehicle Status screen page indicates

to the driver that the function is not available by displaying the

message “Function not available”.

Summary of Contents for 458 Spider





































































































































































































































































Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands

Ferrari 458 Spider, Owner'S Manual

Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands