Ferrari 458 Spider Owner'S Manual Download Page 81

Page: 81 / 260

Safety

TPMS failure

The screen page shown in example

is displayed in the following

circumstances:
- malfunction in the circuit and/or wiring connecting the ECU
- signal is not received by one or more sensors due to a faulty,

broken or ﬂ at battery

- fault in the TPMS ECU.
At the same time, a warning light comes on on the panel (see

page 119) in ﬂ ashing mode for 90 seconds. The warning light then

remains on in ﬁ xed mode until the situation is corrected.
The TYRES screen page cannot be called up by the driver.

System temporarily not active

The screen page shown in example

is displayed in the following

circumstances:
- overheating of sensors
- during calibration (the TPMS ECU does not recognise the

sensors)

- radio frequency that interferes with the wheel sensor signal.

At the same time, a warning light comes on on the panel (see

page 119) in ﬂ ashing mode for 90 seconds. The warning light then

remains on in ﬁ xed mode until the situation is corrected.
The TYRES screen page cannot be called up by the driver.

System not active

For a few seconds at key-on, if the TPMS has been deactivated by a

diagnostic tool, the screen page in example

is displayed.

At the same time, a warning light comes on on the panel (see

page 119) in ﬂ ashing mode for 90 seconds. The warning light then

remains on in ﬁ xed mode until the situation is corrected.
The TYRES screen page cannot be called up by the driver.

TPMS failure

TPMS

temporarily

inactive

TPMS inactive

Summary of Contents for 458 Spider





































































































































































































































































Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands

Ferrari 458 Spider, Owner'S Manual

Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands