Ferrari 458 Spider Owner'S Manual Download Page 162

Page: 162 / 260

162

About your Vehicle

Autopark Function

The EPB Autopark function automatically activates the electric

parking brake when the engine is switched off. At each Key-on, the

Autopark function is always active by default: this means that the

driver does not need to apply the parking brake when the engine is

switched off.
If necessary, the function may be temporarily disabled before

switching off the engine by pressing the

AUTO PARK

button

the message “PARK OFF” is displayed for 5 seconds on the left

hand TFT display. In this case, after the engine is switched off, the

parking brake must be engaged manually by pulling the lever

. To

re-enable automatic EPB engagement at the next key-off, press the

button

again; the message “PARK ON” is displayed for 5 seconds

on the left hand TFT display.

“Automatic Vehicle Holding” AVH function

The Automatic Vehicle Holding function of the electric parking

brake ensures optimised release when moving off from a standstill:

after engine start, the system uses the service brakes to hold the

vehicle instead of the parking brake shoes.

Summary of Contents for 458 Spider





































































































































































































































































Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands

Ferrari 458 Spider, Owner'S Manual

Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands