Ferrari 458 Spider Owner'S Manual Download Page 159

Page: 159 / 260

159

About your Vehicle

Suspension damping delink button

The driver may decide to separate the suspension setting from the

logic of the “Manettino” driving mode control switch using the

special button

on the steering wheel.

By pressing button

, irrespective of the position of the Manettino,

the suspension setting shifts to Level 1 (COMFORT).

Position of

Manettino

Suspension

setting

Button

pressed

WET

COMFORT

remains COMFORT

SPORT

shifts to COMFORT

RACE

shifts to COMFORT

CT OFF

RACE

shifts to COMFORT

ESC OFF

RACE

shifts to COMFORT

If button

has been pressed and subsequently the position of the

Manettino is changed, the suspension setting follows the operating

logic dictated by the Manettino.

Important note

Upon turning off and restarting the vehicle, the suspension

setting depends on the position of the Manettino.

When the Manettino is set to SPORT, RACE, CT OFF or ESC OFF,

shifting to the COMFORT suspension setting by pressing button

is indicated by displaying the special symbol and “Bumpy road”

message on the left TFT display for 5 seconds.

Bumpy road

Summary of Contents for 458 Spider





































































































































































































































































Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands

Ferrari 458 Spider, Owner'S Manual

Search results

Summary of Contents for 458 Spider

Reviews:

Related manuals for 458 Spider

Brands by name

Popular brands